English
Español 
Português 
русский 
Français 
日本語 
Deutsch 
tiếng Việt 
Italiano 
Nederlands 
ภาษาไทย 
Polski 
한국어 
Svenska 
magyar 
Malay 
বাংলা ভাষার 
Dansk 
Suomi 
हिन्दी 
Pilipino 
Türkçe 
Gaeilge 
العربية 
Indonesia 
Norsk 
تمل 
český 
ελληνικά 
український 
Javanese 
فارسی 
தமிழ் 
తెలుగు 
नेपाली 
Burmese 
български 
ລາວ 
Latine 
Қазақша 
Euskal 
Azərbaycan 
Slovenský jazyk 
Македонски 
Lietuvos 
Eesti Keel 
Română 
Slovenski 
मराठी 
Srpski језик 
简体中文 
Esperanto 
Afrikaans 
Català 
שפה עברית 
Cymraeg 
Galego 
繁体中文 
Latviešu 
icelandic 
ייִדיש 
беларускі 
Hrvatski 
Kreyòl ayisyen 
Shqiptar 
Malti 
lugha ya Kiswahili 
አማርኛ 
Bosanski 
Frysk 
ភាសាខ្មែរ 
ქართული 
ગુજરાતી 
Hausa 
Кыргыз тили 
ಕನ್ನಡ 
Corsa 
Kurdî 
മലയാളം 
Maori 
Монгол хэл 
Hmong 
IsiXhosa 
Zulu 
Punjabi 
پښتو 
Chichewa 
Samoa 
Sesotho 
සිංහල 
Gàidhlig 
Cebuano 
Somali 
Тоҷикӣ 
O'zbek 
Hawaiian 
سنڌي 
Shinra 
Հայերեն 
Igbo 
Sundanese 
Lëtzebuergesch 
Malagasy 
Yoruba
Common faults of hook shot blasting machine
2022-02-25
1. The dust of the dust collector contains too many projectiles
Measures: If the air volume is too large, adjust the tuyere baffle appropriately until dust removal can be ensured, but it is advisable to avoid steel sand.
2. The cleaning effect is not ideal
measure:
1. The supply of projectiles is insufficient, increase the projectiles appropriately
2. The projection direction of the second shot blasting machine is incorrect, adjust the position of the directional sleeve according to the instructions
3. There is a slip phenomenon when the elevator lifts the material
Measures: adjust the drive wheel, tension the belt
4. The separator has abnormal noise
Measures: Loosen the inner and outer bolts, tighten the belt
5. The screw conveyor does not send sand
Measures: See if the wiring is correct and reversed
6. The machine starts and stops insensitively or does not act according to regulations
Measures: 1. The relevant electrical components are burned out, check and replace
2. There is too much dust and dirt in the electrical box, and the electrical contact points are in poor contact
3. If the time relay fails, change the time relay, and it is strictly forbidden to adjust the time when driving
7. The hook does not turn or the rubber wheel slips
measure:
1. The weight of the cleaned workpiece exceeds the specified requirements
2. The gap between the rubber wheel and the hook of the reducer is unreasonable, adjust the rotation mechanism
3. The reducer or line is faulty, check the reducer and line
8. The hook goes up and down, and the walking is not flexible
measure:
1. The limit or travel switch is damaged, check and replace
2. The electric hoist is damaged, repair the damaged part
3. The weight of the hook is too light
9. The shot blasting machine vibrates greatly
measure:
1. The blade is seriously worn and the operation is unbalanced, and the balance should be found when the blade is replaced with symmetry or composition.
2. The impeller is seriously worn, replace the impeller
3. The fixing bolts of the shot blasting machine are loose, and the bolts are tightened
10. There is abnormal noise in the blast wheel
measure:
1. The specifications of the steel grit do not meet the requirements, resulting in the phenomenon of sand sticking, and replace the qualified steel grit
Measures: If the air volume is too large, adjust the tuyere baffle appropriately until dust removal can be ensured, but it is advisable to avoid steel sand.
2. The cleaning effect is not ideal
measure:
1. The supply of projectiles is insufficient, increase the projectiles appropriately
2. The projection direction of the second shot blasting machine is incorrect, adjust the position of the directional sleeve according to the instructions
3. There is a slip phenomenon when the elevator lifts the material
Measures: adjust the drive wheel, tension the belt
4. The separator has abnormal noise
Measures: Loosen the inner and outer bolts, tighten the belt
5. The screw conveyor does not send sand
Measures: See if the wiring is correct and reversed
6. The machine starts and stops insensitively or does not act according to regulations
Measures: 1. The relevant electrical components are burned out, check and replace
2. There is too much dust and dirt in the electrical box, and the electrical contact points are in poor contact
3. If the time relay fails, change the time relay, and it is strictly forbidden to adjust the time when driving
7. The hook does not turn or the rubber wheel slips
measure:
1. The weight of the cleaned workpiece exceeds the specified requirements
2. The gap between the rubber wheel and the hook of the reducer is unreasonable, adjust the rotation mechanism
3. The reducer or line is faulty, check the reducer and line
8. The hook goes up and down, and the walking is not flexible
measure:
1. The limit or travel switch is damaged, check and replace
2. The electric hoist is damaged, repair the damaged part
3. The weight of the hook is too light
9. The shot blasting machine vibrates greatly
measure:
1. The blade is seriously worn and the operation is unbalanced, and the balance should be found when the blade is replaced with symmetry or composition.
2. The impeller is seriously worn, replace the impeller
3. The fixing bolts of the shot blasting machine are loose, and the bolts are tightened
10. There is abnormal noise in the blast wheel
measure:
1. The specifications of the steel grit do not meet the requirements, resulting in the phenomenon of sand sticking, and replace the qualified steel grit
2. The inner guard plate of the shot blasting machine is loose, and it rubs against the impeller or impeller blade, adjust the guard plate.
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies.
Privacy Policy